Versions Compared

Version Old Version 28 New Version Current
Changes made by

Akari Tomitaka (冨髙 安果莉)

Akari Tomitaka (冨髙 安果莉)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Released versions:

...

🇦 : Recommended to apply
🇧 : When issue happened
🇨 : Maintenance timing
🇺 : Function / performance improvement

Anchor
V2.70
V2.70

Version 2.70

Release date: October 24, 2024

New Features / Improvements

  • Changed the icons and font for design improvement. 🇺

  • Support camera direct connect to Remote Monitoring without recorders. 🇺

  • Improved ONVIF connection. 🇺

  • Support NTPv3. 🇺

  • Improved the PTZ speed for the following ONVIF commands. 🇺
    ・AbsoluteMove
    ・RelativeMove
    ・GotoPreset
    ・GotoHomePosition

  • Improved the audio transmission speed from PC to the camera. 🇺

Resolved Issues

Fixed the following issues including other minor issues:

  • Corrected an issue where a noise appeared on the image after zooming. 🇨
    Occurrence conditions:
    - [Stabilizer] is on under low light condition.
    - FullHD model

  • Corrected an issue where the setting change of AI application might not be possible on rare occasion. 🇨

  • Corrected an issue where the web browser closed during the PTZ operation using control pad on the detail setting window. 🇨
    Occurrence condition:
    - HTTPS communication
    - Specific version of Google Chrome and Microsoft Edge

  • Corrected an issue where audio output did not work on the live window. 🇨
    Occurrence condition:
    - Network Address Port Translation (NAPT) is configured on the router

  • Corrected an issue where click-to-center PT control might not work for a while after opening a live image on a web browser. 🇨

  • Corrected the SNMP MIB response. 🇨

    Anchor
    V2.63
    V2.63

Version 2.63

Release date: July 26, 2024

Resolved Issues

  • Corrected an issue where the image might gradually get out of focus in version 2.60. 🇨
    Occurrence conditions:
    After auto focus/preset sequence while the frame rate is limited to 15fps(12.5fps*) under the following setting.

    • Extension software is working

    • [Super Dynamic] level is set to 30 or higher

    • [Privacy Mask] is enabled

    • [Stabilizer] is enabled

    • [Maximum shutter] is set to 2/30s(2/25s*) or longer

...

Release date: May 31 2024

New Features / Improvements

  • Changed the font and color on the browser as below:

    • The font of on-screen display (OSD) to Iwata UD 🇺

    • The font of the live and setting windows to NotoSans 🇺

    • The color of i-PPO logo on the live window to black 🇺

  • Removed the need for KMS registration of AI Face Detection. 🇺 View detail
    From this version, issuing and registering the Registration Key are no longer required for AI Face Detection.

  • Added improvements for 3rd party application development. 🇺
    See details at Development Partner Portal.

  • Improved [Control log] to record "AI processor occupancy (Ext. software)" logs properly. 🇺

  • Added [Auto position refresh] on/off setting. 🇺 View detail
    By selecting "On", the position is automatically refreshed when it's misaligned.

  • Improved ONVIF communication. 🇺

Resolved Issues

Fixed the following issues including other minor issues:

...

Release date: Feb. 29 2024
[Update on Apr. 24] To use Vaxtor VaxALPR with this firmware version, update VaxALPR to V1.3.21 or later.

New Features / Improvements

  • Added improvements to enhance security. 🇺
    e.g.,
    - Supports signed firmware
    - [Subject Alternative Name] field has been added to [CA Certificate - Generate Certificate Signing Request] in HTTPS setting. View detail
    - [Security] tab has been added to the [User mng.] setting. View detail

  • Added improvements to the live and setting windows on the web browser. 🇺
    e.g.,
    - A button to show and hide frame rate and bit rate has been added on the live image. View detail
    - HTTP alarm notification setting has been improved. View detail

  • Improved the response to CGI commands. 🇺
    Refer to Command Document (H.265 supported models) at Device integration - IP Camera / i-PRO page.

  • Improved the image quality. 🇺
    For verification results and restrictions on each browser, refer to "Verification of camera performance with Google Chrome, Firefox, and Microsoft Edge (C0132)" on Technical Information.

  • Improved the connectivity to Video Management Software (VMS). 🇺

  • Improved the settings for the extension software AI Privacy Guard. 🇺 View detail
    *Applies only to WV-S61301-Z1.

  • Improved the ONVIF connection. 🇺

Resolved Issues

  • Fixed minor issues. 🇨

    Anchor
    V2.49
    V2.49

...

Release date: Sept 28, 2023
->Updated on Oct 31: Added an item written in red

New Features / Improvements

  • Improved the performance while updating or installing extension software to avoid failure in a slow network. 🇺

  • Enabled all preset positions in Preset sequence 1, 2 and 3 by default. 🇺

  • Changed the [Auto track data in video stream] default setting from "Off" to "On (with live display)" on the [Auto track] tab in [PTZ]. 🇺

  • Improved the image quality. 🇺

  • Improved the Auto Focus performance in low illuminance environments. 🇺

  • Improved the PTZ performance. 🇺

  • Improved the response to the following CGI commands. 🇺

    • /cgi-bin/getdata

    • /cgi-bin/get_capability

    • /cgi-bin/set_sdcard?sdcard=1

  • Improved the ONVIF connection. 🇺

  • Improved the auto tracking behavior. 🇺

  • Improved the data management when updating extension software applications. 🇺

  • Improved the SRTP communication. 🇺

  • Changed the [SNMP] default setting to Off on the [Network] page. 🇺

  • Improved the performance while downloading a video data from an SD memory card in an unstable network. 🇺

Resolved Issues

  • Corrected an issue where the camera showed a blank pop-up of installation status error. 🇨

  • Corrected an issue where the image could not be zoomed out on video management system. 🇨
    Occurrence condition: After maximum zoom by mouse drag. 🇨

  • Corrected an issue where the camera rebooted. 🇧
    Occurrence conditions:
    - [Image capture mode] is "4:3 mode(30fps mode)" or "4:3 mode(25fps mode)"
    - Digital zoom to the maximum level

  • Corrected an issue where an mp4 video recorded on an SD memory card could not be played back on the camera. 🇨
    Occurrence condition: Record an mp4 video with [GOP control] set to "Advanced(Fixed GOP 60s w/1s key-frame)"

  • Corrected an issue where a communication error might occur on the connected i-PRO recorder on rare occasion. 🇨
    Occurrence condition: Start sequence display on the recorder while performing SD memory card recording on the camera.

  • Corrected an issue where the [Save trigger] setting of SD memory recording might unexpectedly changed after firmware update. 🇨

  • Corrected an issue where the camera showed low image quality. 🇨
    Occurrence conditions:
    - [Stabilizer] is On in the [Basic] setting
    - [Frame rate] is set to 8.3fps, 4.2fps or 3.1fps

  • Corrected an issue where the port of [Destination of Trap] was always the default value (162) in the actual operation, even when any other port number is set on the SNMP trap setting. 🇨

  • Corrected an issue where MQTT notification worked only when [AI analytics target] is set to "Other" for audio detection. 🇨

  • Corrected an issue where [Auto track] and [Auto track alarm setting] were disabled when [Maximum shutter] is set to "Max.2/30s" or longer value. 🇨

  • Corrected an issue where the window to set preset positions did not appear when setting VIQS. 🇨

  • Corrected an issue where multi-screen live view might not show images from other cameras. 🇨

    Anchor
    V2.36
    V2.36

Version 2.36

Release date: May 31 2023

Resolved Issues

  • Corrected an issue where a short-term communication error could occur on a connected recorder. 🇨
    Occurrence condition:
    - FIrmware version from 2.10 to 2.33
    - [SD backup rec.] is enabled on the recorder connected to the camera.

    Anchor
    V2.33
    V2.33

...

Release date: March 31, 2023

New Features / Improvements

  • Supports ext4 for SD memory card format. 🇺 View details
    [SD Memory Card File System Format] setting has been added to the [SD memory card] page.

  • Improved the ONVIF connection. 🇺

Resolved Issues

  • Corrected an issue where the camera might reboot. 🇨
    Occurrence conditions:
    - The extension software AI-VMD and AI Privacy Guard are installed and enabled on the camera.
    - The camera is connected to a recorder and “SD backup rec.” is enabled on the recorder’s setting.

  • Corrected an issue where the camera might be slow to start up. 🇨
    Occurrence condition: Multicast auto start is enabled by CGI command.

    Anchor
    V2.30
    V2.30

...

Release date: February 28, 2023

New Features / Improvements

  • Supports new CGI commands. 🇺

  • Supports day and night scene switching on the [Schedule] setting. 🇺 View details #1
    "<Auto-Schedule>Daytime: Image Quality 1/ Night: Image Quality 2" has been added to the [Schedule mode] options.
    *[Scene settings linked to sunrise and sunset times] need to be configured to use this function.

  • Added the On/Off setting to the [SNMP agent setting] in [Network]->[Advanced]->[SNMP]. 🇺
    *Default=On

  • Supports a CGI command to start SD recording when an image transmission stops. 🇺 View details #2

  • Supports editing the camera title on the live window. An edit icon appears next to the camera title. 🇺
    Note: Available for administrator only.

  • Supports a command to send HTTP port number to a 3rd party application. 🇺

  • Changed the default DHCP host name from COM MID1 to i-PRO-<MAC address of camera>. 🇺

  • Improved the FTP/SFTP settings as follows 🇺 View details #3
    - Added 2fps and 3fps to the [Transmission interval] options of [Pre alarm] and [Post alarm]
    - Increased the number of SFTP server setting from 1 to2
    - Added "1920x1080" to the [Image capture size] options of [Pre alarm]

  • Added 0.5s, 1s, 2s, 3s, and 4s to the [Alarm deactivation time] options. 🇺 View details #4

  • Supports replacing %25 with % in the destination address of HTTP alarm notification. 🇺

  • Added "video_server.image.mode" parameters to the CGI command "/cgi-bin/set_imgmode". 🇺

  • Improved the connectivity with i-PRO Configuration Tool (iCT). 🇺

  • Improved [Audio detection] setting so that [AI analytics target] options (Gunshot/ Yell/ Vehicle Horn/ Glass Break) are enabled by default, when [Audio detection] is set to "On". 🇺

  • Changed the text color on the log list for the visibility improvement. 🇺

  • Improved the frame rate during the slow shutter operation under low illuminance condition. 🇺

  • Improved the image quality as follows 🇺
    Image contrast / Auto focus performance during pan-tilt operation / Image brightness during stabilizer operation

  • Improved the ONVIF connection. 🇺

  • Improved the detection accuracy of people detection for extension software. 🇺

  • Supports the extension software AI Scene Change Detection free of charge. 🇺

  • Improved the auto tracking performance. 🇺

Resolved Issues

  • Corrected an issue where the mic input volume from the camera became higher than the selected value. 🇨
    Occurrence condition: Change the [Mic input volume] on the live window.

  • Corrected an issue where it was not possible to reinstall an extension software application after uninstalling it. 🇨
    Occurrence condition: The power of camera is turned off while uninstalling the extension software application.

  • Corrected an issue where the camera could not connect to a recorder and VMS on rare occasion. 🇨
    Occurrence condition: TLS1.3 is selected for [HTTPS-Connection].

  • Corrected an issue where H.265/H.264 live image might not appear. 🇨
    Occurrence condition: Network Address Port Translation (NAPT) is configured on the router

  • Corrected an issue where the image could appear distorted on rare occasion. 🇨

    Anchor
    V2.23
    V2.23

...

Release date: December 16, 2022

Resolved Issues

  • SFTP transmission fails depending on the SFTP server to be connected. 🇨

  • The live image may not appear, as the maximum number of users concurrently accessible to the camera decreases. 🇧
    Occurrence condition:
    When satisfying all of the following conditions:
    - Version 2.10 or 2.20
    - [Internet mode] is set to Off by CGI command
    - H.264/H.265 transmission

...

Release date: September 30, 2022

New Features / Improvements

  • Changed the company name in the GlobalSign digital certificate installed on the camera to "i-PRO Co., Ltd." 🇺

  • Supports the FTP function. 🇺 View details

  • Supports the extension software for 3rd party application. 🇺

  • Added the HTML initialization function. 🇺 (Added on Nov.11, 2022)
    [Load the default HTML files (setup menu).] and [Reset to the default and load the default HTML files.] have been added to the [Default reset] tab.

Resolved Issues

  • The occupancy detection area information is not included in the HTTP alarm notification from the camera. 🇨

  • The frame rate and bit rate may not recover once they drop due to the environmental cause. 🇨

    Anchor
    V2.10
    V2.10

...

Release date: September 15, 2022

New Features / Improvements

  • Updated for the production management. 🇺
    Note: Only the version number has changed

    Anchor
    V1.01
    V1.01

...

Release date: September 15, 2022

Resolved Issues

  • The [Detection sensitivity] setting of VMD area is not reflected in the actual performance. 🇨
    Occurrence condition:
    When satisfying both of the following conditions
    - Preset position is configured
    - VMD area is configured for the preset position

  • The camera may not zoom in smoothly on the image. 🇧
    Occurrence condition: [Stabilizer] is enabled on the [Basic] tab

    Anchor
    V1.00
    V1.00

...